Test Suggestion 6
- Products (69)
- Blogs (4)
- Videos (5)
- Newsroom (1)
- Resource Center (2)
Everything you need for effortless linear motion. A complete kit for an easy yet thorough set-up, this 115RC kit includes the following: two polymer ball carriages (CB0115-CASSRC), 2 end stops (AL0115-STOPRC), four M5 ⅝” barrel nuts, and four star washers.
Everything you need for effortless linear motion. A complete kit for an easy yet thorough set-up, this 115RC kit includes the following: two stainless steel ball carriages (SS0115-CASSRC), 2 end stops (AL0115-STOPRC), four M5 ⅝” barrel nuts, and four star washers.
Come extra-prepared with tools for your undermount solution. Compatible with our 3135EC model, the Eclipse Tool Kit quickens and simplifies drawer box prep with all the tools you need to drill and pre-drill holes and mounting locations for your frames and fixtures. Setting up your project for easy success, the Eclipse Tool Kit is equipped with the following helpers: * 3/32” Drill Bit: This bit works with the Accuride Drilling Jig (4180-0568-XE) to pre-drill holes for disconnect levers. * 4 + ¾”…
Inset installation made simpler! Engineered for use with our 3135EC Eclipse Undermount solution, this bracket kit assists with implementing a flush inset drawer front in need of concealed hardware. Complete with 2 RoHS-compliant inset assemblies with a zinc finish, two #8 32 flat head screws, and an installation guide--all inside a polybag--this kit is also available for bulk orders, fulfilling projects of any scale.
A bracket kit for flush inset drawer fronts. Compatible with our 3135EC undermount solution, this kit includes one pair of bottom inset bracket assemblies in a zinc finish, adding ease and precision to alternative frames and mounting styles. For thorough installation, a rear face frame bracket (4180-0656-XE) is also required. Along with both brackets, this single kit also comes with two each #8-32 flat head screws, and an installation guide inside a polybag. Cabinet mounting screws are not…
Compatible with the CBLIFT-0019 Ascent, this bracket kit provides the means to attach a flat panel screen to your motion hardware (fasteners included)
Pilaster kit for use on 3832 and 2132 slides.
Mounting bracket kit for 1145 or 1155 Flipper Door Slides
-
Go with the Accuride Original line of motion hardware. Complete with enhanced strength and movement, full-extension, and a lever-disconnect, the 3832E model is a classic drawer slide that fits a wide range of uses including but not limited to: pull-out shelves, kitchen utensil drawers, and point-of-sales trays. * Supports loads up to 100 lbs. * For drawers up to 24” wide * For additional technical information see below A patented Cam Drawer Adjust allows for precise vertical adjustment, while a…
Over the moon for over-travel? So are we. Our Model 3634 is designed to enhance wider drawers, shelves, and storage bins that require full access–from household kitchens to business or medical offices, and even retail stores. * Side-mount load capacity up to 200 lbs. per pair with drawer width of 42" * Flat mount load capacity up to 75 lbs. per pair with drawer width of 24" * Recommended drawer box size 1 + 9/16" less than the cabinet opening * For additional technical information see below With…
Compatible with models 1332 and 1432, this carrier strip kit is sold separately from D-Pack hardware kits and optimizes pocket and flipper door installation. Each kit includes two black hinge carrier strips, 3 stainless steel connector clips, six #8 x ⅜” black pan head screws (without hinge base plate), six #8 x ⅝” zinc flat head screws (with hinge base plate), and one “Caution” sticker.
Compatible with models 1332 and 1432, this carrier strip kit is sold separately from D-Pack hardware kits and optimizes pocket and flipper door installation. Each kit includes two zinc hinge carrier strips, 3 stainless steel connector clips, six #8 x ⅜” black pan head screws (without hinge base plate), six #8 x ⅝” zinc flat head screws (with hinge base plate), and one “Caution” sticker.
