Installation
- Products (83)
- Blogs (8)
- Videos (11)
- Newsroom (7)
- Resource Center (1)
…Detail Page Lightweight material packed with maximum endurance. Engineered with pre-drilled holes and specially designed to accommodate side-, flat-, and vertical-mounting techniques, this aluminum rail serves as the foundation for the FG115 Linear Friction Guide. Self-lubricated for seamless motion, FG115 rails can be cut to a determined length or butted together for an extended span of travel. For optimal performance and longevity, utilize all fixing holes when installing this hardware.
…Lightweight + Low-maintenance. One meter longer than its counterpart (FG115-0100T), this rail is made from the same hard anodized aluminum that serves as the basis for the FG115 Linear Motion Guide's fluid movement and tough outer coating that requires minimal upkeep. Self-lubricated for seamless motion, FG115 rails can be cut to a determined length or butted together for an extended span of travel. For optimal performance and longevity, utilize all fixing holes when installing this hardware.
Return to 116RC Product Detail Page The sum of its parts. A component within the Sliding Door Hardware Kit for the 116RC Heavy-Duty Linear Track System, this 142” fascia is crafted from anodized aluminum and clips onto its support beam (AL0116-SUPPRC) for a sleek, completed design. For extra easy-access, an installer can lift and hook the fascia open to reach the track and fittings responsible for linear motion.
…¾” Drill Extension: Paired with the 3/32” Drill Bit, this extension improves access when pre-drilling disconnect lever holes at the required 10-degree angle. * #2 x 4” Phillips Point Screwdriver Bit: The length on this bit gives installers better access when installing the screws for the disconnect levers. * ¼” Brad Point Drill Bit: This bit is designed for drilling the hook holes in the back of the drawer. If used with the Accuride Drilling Jig, no measuring is required. * ¼” Stop Collar: Used…
The Accuride ST8210 is the smart option for movement in commercial kitchen appliances. The NSF-certified roller-bearing slide is easy to install and needs little maintenance. Over two inches of extra travel gives you full reach of items in the back of a drawer or tray. The extra room makes searching, sorting, and retrieving items easier, saving time (and money). The ST8210 also has a self-close and auto lock-in design to ensure drawers close properly. * Side-mount * For loads up to 230 lbs *…
The Accuride ST8211 is the smart option for movement in commercial kitchen appliances. The NSF-certified roller-bearing slide is easy to install and needs little maintenance. Over two inches of extra travel gives you full reach of items in the back of a drawer or tray. The extra room makes searching, sorting, and retrieving items easier, saving time (and money). The ST8211 also has a self-close and auto lock-in design to ensure drawers close properly. * Bottom-mount * For loads up to 230 lbs *…
Compatible with models 3832E, 3832EDO, 3832ESC, 3832EHDSC, CH3832, 3732, 3834, 2109, and 2132, this 22” Clip-On Bracket enables bottom or platform mounting for side-mount ball bearing slides while supplying a simple, tooless installation. Note: brackets are sold singly, and two are required per a pair of slides.
Return to 116RC Product Detail Page Ensuring ease from start to finish. Engineered specifically for the 116RC model, these aluminum end stops ensure that your linear track system ends its length of travel safely and soundly--without slamming or rattling shut. Each order comes with two end stops crafted from corrosion-resistant aluminum and two screws for a breezy installation.
Return to 115RC Product Detail Page Ensuring ease from start to finish. Sold separately or within either 115RC kit (4180-0756-XE/4180-0746-XE), these aluminum end stops ensure that your linear track system ends its length of travel safely and soundly--without slamming or rattling shut. Each order comes with one end stop crafted from corrosion-resistant aluminum and two screws for a breezy installation.
Compatible with our 1332 solution and accommodating pocket doors ¾” to 13/16” thick, this hinge kit provides the extra tools you need for an inset installation. Each order includes two 35mm salice black clip-on hinges, two 3mm mounting base plates, two 3mm hinge base spacers, two hinge arm cover caps, four #6 x ⅝” Phillips flat head screws, and one “Caution” door sticker.
Compatible with models 3832E, 3832EDO, 3832ESC, 3832EHDSC, CH3832 3732, and 3834, this 14” Clip-On Bracket enables bottom or platform mounting for side-mount ball bearing slides while supplying a simple, tooless installation. Note: brackets are sold singly, and two are required per a pair of slides.
Compatible with models 3832E, 3832EDO, 3832ESC, 3832EHDSC, CH3832, 3732, 3834, 2109, and 2132, this 16” Clip-On Bracket enables bottom or platform mounting for side-mount ball bearing slides while supplying a simple, tooless installation. Note: brackets are sold singly, and two are required per a pair of slides.